PDA

Visualizza Versione Completa : Bettas4all Standard: Chapter 3D - Doubletail Plakat



Roberto Silverii
14-01-2014, 12:15
Chapter 3D: Finnage Characteristics Doubletail Plakat


Under Construction
Figure 3D.1 2D representation of the 3D model of the ideal doubletail plakat (created by Stefan George Psarakos).


1. General appearance


1.1 Condition
As in all other show betta (see Chapter 3).


1.2 Deportment
As in all other show betta (see Chapter 3).


1.3 Overall balance
As the name indicates, the ideal doubletail plakat has a symmetrical appearance which can be demonstrated by an imaginary horizontal midline which shows that the upper and lower part of the fish nearly form a mirror-image (see Figure 3D.2). The contour of the ideal doubletail plakat fits an oval of which the width is approximately 1.5-times the height. The outer rim of the unpaired fins follows the contours of the oval in a smooth way without any irregularities. Ideally the anal fin and dorsal fin should not extend beyond the bottom edge and upper edge of the caudal fin, respectively.


Under Construction
Figure 3D.2 The contour of the ideal doubletail plakat fits an oval. The horizontal (X) and vertical (Y) midlines as well as vertical lines A-E are used to describe the proportions of the ideal doubletail plakat.




The vertical line which runs through the point on the body where the outer rays of the caudal fin are attached (C), divides the total length of the doubletail plakat (A-E) into two parts, A-C and C-E, with a ~75/25 distribution respectively (see Figure 3D.2). An important point with respect to overall balance is that the finnage must be in proportion with the body. The width of the anal fin (B-C) is used as an important marker to indicate the desired proportions (see Figure 3D.3). In the ideal situation the length of the rays of the caudal fin, which extend from the peduncle (D) to the outer rim (E), are equal to 1/2 of the width of the anal fin (B-C). When an imaginary vertical midline would be drawn, the vertical length of the dorsal and anal fin from the body to the outer rim is again equal to 1/2 of the width of the anal fin. The length of the ventral fins from the point where they are attached to the body to the tip is equal to 1/2 to 2/3 of the width of the anal fin (B-C).


Under Construction
Figure 3D.3 The width of the anal fin (B-C) is an important marker to demonstrate proportion.


2. Body


2.1 Form & dimension
As in all other show betta (see Chapter 3 and Figure 3D.4).


Under Construction
Figure 3D.4 Ideal body shape form & dimension of the doubletail plakat.


2.2. Scalation
As in all other show betta (see Chapter 3).


3. Finnage


3.1 Caudal fin
The caudal fin of the doubletail plakat is characterized by two caudal lobes. The two caudal lobes are allowed to overlap but should be separated by means of a split which runs up to the base of the peduncle. The form of the two caudal lobes of the doubletail plakat together can be compared with a the shape of a capital letter D (see Figure 3D.5, left). The caudal fin has a symmetrical appearance which means that if an imaginary horizontal midline (X) would be drawn this line ideally should overlap the split which divides the caudal in two equally sized lobes. The ideal caudal fin has a 180-degree spread (both caudal lobes together), straight rays and sharp corners. A spread of more than 180-degrees is not preferred over a 180-degree spread. Each caudal lobe should possess 12-13 primary rays which extend from the peduncle and ideally the branching of the rays can range from secondary (4-ray) to tertiary (8-ray) branching. The branching of the rays should be evenly distributed throughout the caudal fin. The webbing of the caudal fin has a smooth appearance without any overlapping/folding parts due to excessive branching and/or webbing.


Under Construction
Figure 3D.5 Ideal form of the caudal fin (left) and dorsal fin (right) of the doubletail plakat.


3.2 Dorsal fin
At first sight, the dorsal fin of the doubletail plakat approximately resembles the shape of the anal fin. The dorsal fin of the doubletail plakat snaps open like a fan and has the shape of a modified scalene trapezoid (see Figure 3D.5, right). The volume and the capacity of the dorsal fin to open up like a fan is achieved by an increase in branching of the rays (mostly secondary or tertiary branching) and an increase of rays (ranging from 18-21 rays). Ideally the base of the dorsal fin should be equal to 7/8 of the width of the anal fin (B-C). Please note that the point where the rays of the back of the dorsal are attached to the body, is located closer to the caudal peduncle (C) than seen in singletail bettas. The rays in the back of the dorsal fin match those of the caudal fin but the length of the rays slightly declines towards the front. The rays in the front of the dorsal must be slighlty directed forward, and the back of the dorsal fin overlaps the upper part of the caudal. Overlap of the back of the dorsal fin with the body is not desirable. The webbing of the dorsal fin has a smooth appearance without any overlapping/folding parts due to excessive branching and/or webbing.


3.3 Anal fin
The anal fin of the doubletail plakat starts at the thickest point of the body (B) and has the shape of a modified scalene trapezium (see Figure 3D.6, right). The anal fin runs approximately parallel to the body. The length of the rays in the back of the anal fin match those of the caudal fin but the length of the rays slightly declines towards the front. During flaring the front of the anal is directed forward and the back overlaps the lower part of the caudal. The volume and the capacity of the anal fin to open up during flaring is achieved by a moderate branching of the fin-rays (mainly primary raysplitting although secondary raysplitting sometimes also can be observed). The webbing of the anal fin has a smooth appearance without any overlapping/folding parts due to excessive branching and/or webbing.


3.4 Ventral fins
The form of the ventrals fins of a doubletail plakat is as in all other show betta (see Chapter 3). Additionally, the ventrals of the doubletail plakat should have a full volume (see Figure 3D.6, left).


3.5 Pectoral fins
As in all other show betta (see Chapter 3 and Figure 3D.6, right). The pectoral fins of the doubletail plakat are D-shaped with primary (2-ray) branching.


Under Construction
Figure 3D.6 Ideal form of the ventral & pectoral fins (left) and anal fin (right) of the doubletail plakat.


http://www.hollandbettashow.com/bettas4all_photos/Bettas4allStandard/Chapter3DFig3D-7.jpg
Figure 3D.7 Examples of doubletail plakat males
(A) Krung Krodsrimai (Profish Farm; Thailand), (B) was bred by Sanya Ponpal (Interbettas; Thailand) and (C) was bred by Tada palakul (Smilebetta; Thailand)
Please note that these fish are examples and still exhibit points requiring improvement.


It is not allowed to copy, translate or use the content of this standard without permission of the author.